CCNA Managing An Internetwork MCQs
CCNA Managing An Internetwork MCQs
The following CCNA Managing An Internetwork MCQs have been compiled by our experts through research, in order to test your knowledge of the subject of CCNA Managing An Internetwork. We encourage you to answer these 30 multiple-choice questions to assess your proficiency.
Please continue by scrolling down.
1: A proprietary protocol designed by Cisco to help administrators collect information about both locally attached and remote devices
A. Copy current version to tftp server
B. Router#exit
C. Cisco Discovery Protocol (CDP)
D. CDP is a Cisco proprietary protocol; CDP is a Data Link layer protocol; CDP can discover directly connected neighboring Cisco devices
2: Turn CDP on for an interface
A. Flash
B. Cdp enable
C. Router#sh cdp entry * protocol
D. Terminal monitor
3: The IOS version of your directly connected neighbors
A. Show cdp neighbor detail or show cdp entry *
B. Flash - TFTP server - ROM
C. Router#sh cdp entry * version
D. Cisco Discovery Protocol (CDP)
4: Rommon 1 > confreg 0x2142
A. Show cdp neighbor
B. Change the configuration register to turn on bit 6
C. Ctrl+Shift+6 - then X
D. Router#exit
5: How will a 2600 series router respond if the conditions listed below exist during the boot process?
A. POST (power-on self-test)
B. The router will enter ROM monitor mode
C. Configuration register
D. Copy tftp flash
6: Displays information about interface traffic - including the number of CDP packets sent and received and the errors with CDP
A. Flash memory
B. NVRAM should be erased and the router restarted
C. Telnet
D. Router#sh cdp traffic
7: See the current value of the configuration register and IOS version
A. Router#disconnect ?
B. Flash memory
C. Sh ver
D. Router#sh hosts
8: Turn off domain-lookup
A. Todd2509(config)#no ip domain-lookup
B. Restore router config
C. Access control list is filtering Telnet & The VTY password is missing
D. Show version
9: You are consoled into a router and you see the following output...
A. Router#exit
B. Show cdp neighbor
C. To verify that the CPU utilization is low enough to handle the effects of a debug command
D. No debug all
10: What keystrokes can you use to telnet into multiple devices simultaneously?
A. Ctrl+Shift+6 - then X
B. The configuration register setting is incorrect.
C. Erase the config
D. Verify current router config
11: Router#copy run start
A. Mini-IOS
B. Config mem
C. Copy current version to NVRAM
D. RAM (random-access memory)
12: You telnet to a router and make your necessary changes; now you want to end the Telnet session. What command do you type in?
A. Restoring or Upgrading the Cisco Router IOS
B. Configuration register
C. Disconnect
D. Show version
13: A 16-bit configurable value stored in hardware or software that determines how Cisco routers function during initialization.
A. Flash memory
B. Show interfaces; show ip route; ping
C. Show sessions
D. Configuration register
14: Used to control how the router boots up. This value can be seen with the show version command and typically is 0x2102 - which tells the router to load the IOS from flash memory as well as to load the configuration from NVRAM.
A. Configuration register
B. CDP is a Cisco proprietary protocol; CDP is a Data Link layer protocol; CDP can discover directly connected neighboring Cisco devices
C. Boot a small IOS from ROM
D. Mini-IOS
15: Router#copy tftp flash
A. Router>trace
B. Restoring or Upgrading the Cisco Router IOS
C. The configuration register setting is incorrect.
D. CDP is a Cisco proprietary protocol; CDP is a Data Link layer protocol; CDP can discover directly connected neighboring Cisco devices
16: Stored in the microcode of the ROM - the ROM monitor is used for manufacturing - testing - and troubleshooting.
A. Erase the config
B. RAM (random-access memory)
C. ROM monitor
D. Restoring or Upgrading the Cisco Router IOS
17: You are unsuccessful in telnetting into a remote device. What could the problem be? (Choose two)
A. Router#sh users
B. Copy start tftp
C. No debug all
D. Access control list is filtering Telnet & The VTY password is missing
18: Displays information about each interface using CDP - including the encapsulation on the line - the timer - and the holdtime for each interface.
A. Router#sh cdp int
B. Access control list is filtering Telnet & The VTY password is missing
C. Config mem
D. ROM monitor
19: You telnet into a router and you receive the following message: Password required but none set. Why was this message received?
A. 0x2102
B. Restoring or Upgrading the Cisco Router IOS
C. No VTY password has been set.
D. Verify stored config
20: Delivers information about directly connected devices
A. Router#sh hosts
B. Copy flash tftp
C. Sh version
D. Router#sh cdp nei
21: See the connections made from your router to a remote device
A. Router#sh sessions
B. Config mem
C. Todd2509(config)#ip name-server {IP address of DNS Server}
D. Router(config)#cdp holdtime 240
22: Which three statements accurately describe CDP?
A. CDP is a Cisco proprietary protocol; CDP is a Data Link layer protocol; CDP can discover directly connected neighboring Cisco devices
B. It is used to bypass the configuration in NVRAM
C. Todd2509(config)#no ip domain-lookup
D. POST (power-on self-test)
23: Called the RXBOOT or bootloader by Cisco - the mini-IOS is a small IOS in ROM that can be used to bring up an interface and load a Cisco IOS into flash memory. The mini-IOS can also perform a few other maintenance operations.
A. Configuration register
B. Mini-IOS
C. Disconnect
D. Ctrl+Shift+6 - then X
24: What is the command to copy a Cisco startup-config file to a TFTP server?
A. RAM (random-access memory)
B. Router#sh cdp
C. Temporary DNS entries; Permanent name-to-address mappings created using the ip host command
D. Copy start tftp
25: If you want to have more than one Telnet session open at the same time - what keystroke combination would you use?
A. Ctrl+Shift+6 - then X
B. Backing Up the Cisco IOS
C. Cdp enable
D. Router#sh cdp entry * version
26: Turn off CDP completely
A. Router#sh processes
B. Router#exit
C. No cdp run
D. Backing Up the Cisco IOS
27: The corporate office sends you a new router to connect - but upon connecting the console cable - you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?
A. NVRAM should be erased and the router restarted
B. NVRAM (nonvolatile RAM
C. Access control list is filtering Telnet & The VTY password is missing
D. Router#sh cdp traffic
28: POST tests (in ROM) > Bootstrap loads IOS (from Flash - TFTP Server or ROM) > IOS loads startup-config from NVRAM > Startup Config loads or router is brought up in setup mode
A. Show cdp neighbor detail or show cdp entry *
B. Router>trace
C. Erase the config
D. The Router Boot Sequence
29: Verify the amount of flash memory and the file or files being stored in flash memory
A. Sh flash
B. Copy start run
C. RAM (random-access memory)
D. Copy tftp flash
30: Router(config)#config-register 0x2101
A. Boot a small IOS from ROM
B. Show interfaces
C. The configuration register setting is incorrect.
D. Copy flash tftp
31: What command can you use to see the hostname - local interface - platform - and remote port of a neighbor router?
A. Reset the router
B. Show cdp neighbor
C. Copy current version to NVRAM
D. NVRAM (nonvolatile RAM
32: What information is displayed by the show hosts command? (Choose two.)
A. Temporary DNS entries; Permanent name-to-address mappings created using the ip host command
B. Copy flash tftp
C. You must use the terminal monitor command
D. Router#sh sessions
List of CCNA Managing An Inter...
Available in:
CCNA Managing An Internetwork MCQs
